Language
Cart

Page 18 - Latest News

  1. 80 SWIVEL SEAL Double-Acting Polyurethane, Rod Sealing for Rotary Pressure Applications
    25
    May

    80 SWIVEL SEAL Double-Acting Polyurethane, Rod Sealing for Rotary Pressure Applications

    DESIGN
    The Hallite 80 double-acting swivel seal, or rotary pressure seal, is designed specifically for use in hydraulic swivel joints with an internal rotating rod, particularly in housings to Asian design. This design is a one-piece seal that can
    replace the two part seals typically used in this application. The Hallite 80 has a moulded groove in the dynamic face to improve sealing against the surface while trapping lubrication and reducing the surface contact area and thereby reducing running friction. Special pressure activation grooves are incorporated into design of the seal to enable an immediate seal of the joint. The Hallite 80 is manufactured in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation, excellent low temperature performance, and long service life.

    Read more
  2. Hallite 53 Double Acting Piston Seal (DAS)
    21
    May

    Hallite 53 Double Acting Piston Seal (DAS)

    A robust assembly designed specifically for one piece pistons, the Hallite 53 double acting seal uses a rubber sealing element which has proved itself in service to be extremely wear resistant and capable of working most effectively in a wide variety of medium duty applications. The seal is also suitable for two piece pistons.

    The assembly comprises a rubber seal, two split support rings and two split bearings, one of each located either side of the seal.

    The nitrile rubber seal is designed to have its section compressed by the housing, to ensure a low pressure seal and , when pressurised, be protected from extrusion damage by the extending lips of the support ring. The support ring is manufactured from a tough flexible polymer and scarf cut for assembly.

    The proportions of the range have been determined to give a satisfactory performance when used with the recommended operating conditions.

    Read more
  3. Hallite 33
    20
    May

    Hallite 33

    Design
    The Hallite 33 wiper has a lip designed to remove lightly adhered dirt from the rod i.e. mud, dust or moisture. The wiper is manufactured from a hard nitrile rubber suitable for installing in a grooved housing. Rod diameters (Ød1) of 20mm and below require a two piece housing .To prevent dirt passing the outside of the wiper and to reduce the pumping action, the outside diameter is an interference fit with the housing. Certain sizes of the standard Hallite 33 metric range are suitable for ISO 6195 Housing Type A. It should also be noted that the Hallite 33 inch profile differs from the metric profile. NB: Part numbers suffixed by “‡” indicate housing sizes to meet ISO6195A. Many of the metric sizes are also available as  polyester wipers – see Hallite 38.

    Read more
  4. Hallite 754  PISTON SEAL Double-Acting Polyester Face with Pre-Loaded O-Ring
    19
    May

    Hallite 754 PISTON SEAL Double-Acting Polyester Face with Pre-Loaded O-Ring

    The Hallite 754 double-acting piston seal is a compact, low friction seal for light to medium duty applications. The Hallite 754 is comprised of a tough, wear-resistant thermoplastic elastomer face seal which is pre-loaded by a NBR O-ring. The face material comes in a number of material options to extend operating conditions. The housing width allows a narrow width piston to be used. We recommend that an adequate bearing, such as the Hallite 506 or 87 bearing strip, is mounted on one or both sides of the seal. For further details of bearing grooves, please refer to the appropriate product data sheet.

    Read more
  5. Hallite 511 ROD/PISTON SEAL Single-Acting TPU/TPE with O-Ring Energizer
    18
    May

    Hallite 511 ROD/PISTON SEAL Single-Acting TPU/TPE with O-Ring Energizer

    DESIGN
    The Hallite 511 is a standard profile loaded U-cup with precision trimmed sealing lips manufactured in either a polyurethane or polyester shell energised by a high quality O-ring and designed for common North American square grooves. At zero or low pressure, the O-ring helps to increase the sealing force preventing any bypass. Under most conditions as the pressure rises, the sealing force increases and the O-ring ensures complete lip actuation.

    Read more
  6. Hallite 513 ROD/PISTON SEAL Single-Acting TPU/TPE with O-Ring Energizer
    13
    May

    Hallite 513 ROD/PISTON SEAL Single-Acting TPU/TPE with O-Ring Energizer

    The Hallite 513 is a standard profile loaded U-cup with precision trimmed sealing lips manufactured in either a polyurethane or polyester shell energised by a high quality O-ring and designed for common North American grooves. The sealing lips are trimmed at an angle to give optimal rod sealing performance. In most cases, the deep profile of the Hallite 513 provides extra stability needed to resist rolling in the groove. Together these features result in improved life and sealing.

    Read more
  7. Hallite 506 BEARING
    11
    May

    Hallite 506 BEARING

    The Hallite 506 is available in three forms: cut bearing rings, spiral lengths, and flat coils. Spiral lengths and flat coils are recommended to customers who want to cut their own custom sizes. Spiral lengths are recommended to distributors or customers who may need to fit a wide range of application sizes in a particular cross section.

    Read more
  8. Hallite 520 single lipped
    11
    May

    Hallite 520 single lipped

    The Hallite 520 single-lipped, snap-in rod wiper is designed to fit North American D-style housings. The proportions of the wiping lip ensure that contact is maintained with the surface of the rod to remove heavily deposited containments such as mud and ice.

    Read more
  9. Hallite 839
    07
    May

    Hallite 839

    F E A T U R E S

    • • ISO housing range
    • • Double lips ensures drier sealing system
    • • Long life and long wear
    • • Easy to install
    Read more
  10. Hallite 780 Double Acting Piston Seals
    07
    May

    Hallite 780 Double Acting Piston Seals

    The Hallite 780 double-acting piston seal in a robust five part assembly is designed specifically for one piece pistons in a wide range of medium duty applications. The seal is also suitable for two piece pistons.

    Read more
Posts loader