Language
Cart

Page 7 - Hydraulic Seal

  1. Hallite 58 Double Acting Piston Seal
    25
    May

    Hallite 58 Double Acting Piston Seal

    The Hallite 58 double acting piston seal combines the Hallite 56 seal with bearing rings to give a very robust heavy duty seal assembly for split pistons. It enables the designer to use large clearances and, with the integral bearing rings, to restrict the piston length.

    The assembly comprises a seal and two L shaped bearings. The centre of the seal is rubber which is bonded to two ‘U’ section bases of rubberised fabric, and is compressed by the housing to obtain an effective low pressure seal. When the pressure increases the rubber energises the ‘U’ section and deforms it to the housing, increasingthe sealing area and improving the seal.

    Rubberised fabric is used to protect the rubber, because it has strength and durability which combines with its ability to retain lubricant to help keep friction low and reduce wear.

    Supporting the seal at either end is a polyacetal bearing proportioned to react to the pressure on the seal to prevent extrusion damage, and support the piston in its side load.

    Read more
  2. Hallite 755 Double-Acting Piston Seal
    25
    May

    Hallite 755 Double-Acting Piston Seal

    DESIGN
    The Hallite 755 double-acting piston seal is a compact, low friction seal for light to medium duty applications designed originally to fit North American NFPA groove standards. The Hallite 755 is comprised of a tough, wear-resistant thermoplastic elastomer face seal which is pre-loaded by a square cross-section NBR expander. The face material comes in a number of material options to extend operating conditions. The housing width allows a narrow width piston to be used. We  ecommend that an adequate bearing, such as the Hallite 506 or 87 bearing strip or the Hallite 533 molded bearing, is mounted on one or both sides of the seal. For further details of bearing grooves, please refer to the appropriate product data sheet

    Read more
  3. Hallite 606 PISTON SEAL
    25
    May

    Hallite 606 PISTON SEAL

    DESIGN
    The Hallite 606 single-acting, single lip asymmetric piston seal is designed with precision trimmed sealing lips to provide effective bore sealing in light and medium-duty applications. The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are trimmed at an angle to give optimal rod sealing performance. The range covers most standard housings used in Europe, North America and Asia. The Hallite 606 is designed to have an interference in the seal housing groove. The outer dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-rings. The seal is recommended for use in single-acting piston seal applications. It can also be fitted back-to-back in separate grooves for use in double-acting applications. The Hallite 606 is moulded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance

    Read more
  4. Hallite 831 WIPER Single-Lipped Polyurethane Designed for Metric Housings
    25
    May

    Hallite 831 WIPER Single-Lipped Polyurethane Designed for Metric Housings

    DESIGN

    The Hallite 831 single lipped, snap-in rod wiper is designed to fit metric housings and is interchangeable with many common European wiper styles. The proportions of the wiping lip ensure that contact is maintained with the surface of the rod to
    remove all deposits of mud and other forms of contamination except for those found in heavy-duty industrial applications. The outside diameter of the seal incorporates a crush lip to provide interference fit with the housing and a face bead to ensure that the crush lip is not trapped in the corner of the housing. These features help prevent contaminant from entering the groove. The moulded ribs on the internal diameter provide extra stability to the wiper and help prevent the possibility of blow-out due to pressure trapping between the wiper and the main rod seal. The Hallite 831 is moulded in polyurethane for maximum wear resistance and performance.

    Read more
  5. Hallite 842 WIPER
    25
    May

    Hallite 842 WIPER

    DESIGN
    The Hallite 842 single-lipped, snap-in rod wiper is developed specifically for use in harsher environments with heavy contamination, such as in agriculture, offhighway, forestry, and long wall mining equipment. The unique feature of the Hallite 842 is the Umbrella Wiper Technology™, which is a protective debris guard flap on the wiping lip that entirely covers the gland housing and prevents the water/slurry trap that is common with conventional wipers. This feature offers added protection to the integrity of the hydraulic system, providing increased system life by reducing corrosion and preventing the ingress of contamination into the wiper housing groove and hydraulic cylinder gland. The moulded ribs on the internal diameter provide extra stability to the wiper and help prevent the possibility of blow-out due to pressure trapping between the wiper and the main rod seal. The standard Hallite 842 is moulded in Hythane® 181, Hallite’s high-performance
    polyurethane, for easy installation and excellent low temperature performance. A number of sizes, indicated by “*”, do not have an interference fit between the outside diameter of the wiper and the wiper housing bore ØD₁. They float on the retaining lip.

    Read more
  6. Hallite 834 WIPER
    25
    May

    Hallite 834 WIPER

    DESIGN
    The Hallite 834 single lipped, snap-in rod wiper is designed to fit standard housing,including many ISO 6195E sizes. The proportions of the wiping lip ensure that contact is maintained with the surface of the rod to remove all deposits of mud and other forms of contamination except for those found in heavy industrial applications. The moulded ribs on the internal diameter provide extra stability to the wiper and help prevent the possibility of blow-out due to pressure trapping between the
    wiper and the main rod seal. The Hallite 834 is precision moulded in Hythane® 181 for maximum wear resistance. For better dry rod performance and protection against moisture ingress, the Hallite technical team may advise you to use a Hallite 846 wiper instead of the Hallite 834.

    Read more
  7. 80 SWIVEL SEAL Double-Acting Polyurethane, Rod Sealing for Rotary Pressure Applications
    25
    May

    80 SWIVEL SEAL Double-Acting Polyurethane, Rod Sealing for Rotary Pressure Applications

    DESIGN
    The Hallite 80 double-acting swivel seal, or rotary pressure seal, is designed specifically for use in hydraulic swivel joints with an internal rotating rod, particularly in housings to Asian design. This design is a one-piece seal that can
    replace the two part seals typically used in this application. The Hallite 80 has a moulded groove in the dynamic face to improve sealing against the surface while trapping lubrication and reducing the surface contact area and thereby reducing running friction. Special pressure activation grooves are incorporated into design of the seal to enable an immediate seal of the joint. The Hallite 80 is manufactured in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation, excellent low temperature performance, and long service life.

    Read more
  8. Hallite 53 Double Acting Piston Seal (DAS)
    21
    May

    Hallite 53 Double Acting Piston Seal (DAS)

    A robust assembly designed specifically for one piece pistons, the Hallite 53 double acting seal uses a rubber sealing element which has proved itself in service to be extremely wear resistant and capable of working most effectively in a wide variety of medium duty applications. The seal is also suitable for two piece pistons.

    The assembly comprises a rubber seal, two split support rings and two split bearings, one of each located either side of the seal.

    The nitrile rubber seal is designed to have its section compressed by the housing, to ensure a low pressure seal and , when pressurised, be protected from extrusion damage by the extending lips of the support ring. The support ring is manufactured from a tough flexible polymer and scarf cut for assembly.

    The proportions of the range have been determined to give a satisfactory performance when used with the recommended operating conditions.

    Read more
  9. Hallite 33
    20
    May

    Hallite 33

    Design
    The Hallite 33 wiper has a lip designed to remove lightly adhered dirt from the rod i.e. mud, dust or moisture. The wiper is manufactured from a hard nitrile rubber suitable for installing in a grooved housing. Rod diameters (Ød1) of 20mm and below require a two piece housing .To prevent dirt passing the outside of the wiper and to reduce the pumping action, the outside diameter is an interference fit with the housing. Certain sizes of the standard Hallite 33 metric range are suitable for ISO 6195 Housing Type A. It should also be noted that the Hallite 33 inch profile differs from the metric profile. NB: Part numbers suffixed by “‡” indicate housing sizes to meet ISO6195A. Many of the metric sizes are also available as  polyester wipers – see Hallite 38.

    Read more
  10. Hallite 754  PISTON SEAL Double-Acting Polyester Face with Pre-Loaded O-Ring
    19
    May

    Hallite 754 PISTON SEAL Double-Acting Polyester Face with Pre-Loaded O-Ring

    The Hallite 754 double-acting piston seal is a compact, low friction seal for light to medium duty applications. The Hallite 754 is comprised of a tough, wear-resistant thermoplastic elastomer face seal which is pre-loaded by a NBR O-ring. The face material comes in a number of material options to extend operating conditions. The housing width allows a narrow width piston to be used. We recommend that an adequate bearing, such as the Hallite 506 or 87 bearing strip, is mounted on one or both sides of the seal. For further details of bearing grooves, please refer to the appropriate product data sheet.

    Read more
Posts loader