K17 PISTON SEAL 145X124X8.1

K17 is a two piece double acting piston seal which consists of one special mixture PTFE profile ring and an o-ring as energizing element.

PRODUCT ADVANTAGES
• Low friction , free of stick-slip
• Simple groove design and low axial housing heights
• Long service life
• High sliding speed
• Wide range of temperature and chemicals depending on the o-ring material
• Minimum static and dynamic friction coefficient for a minimum energy loss and operating temperature
• Wide range of dimensions

APPLICATION
Injection moulding machines , fork-lift trucks , loading platforms , cranes , agricultural machinery and valves for hydraulic and pneumatic systems.

MATERIAL		CODE
NBR	70 SHORE A	NB^₇₀₀₁
PTFE		PT^₆₀₀₃

OPERATING CONDITIONS
MEDIA	Mineral oils(DIN 51524)	HFA ve HFB	HFC
TEMPERATURE	-30°C +105°C	+5°C +60°C	-30°C +60°C
PRESSURE	≤400 Bar	≤400 Bar	≤400 Bar
SPEED	≤5.0 m/sn	≤5.0 m/sn	≤5.0 m/sn
Note: The above data are maximum values and cannot be used at the same time.

SURFACE ROUGHNESS

Ra

Rmax

Sliding Surface ØD

≤0.2 μm

≤2.0 μm

Groove Base Ød

≤1.6 μm

≤6.3 μm

Groove Flanks B

≤3.2 μm

≤15 μm

Note: It is recommended to have 50% to 90% of the working surface material contact area value.

INSTALLATION
We recommend using special assembly tool (See section; Hydraulic Sealing Elements General Installation Information) and to have open groove design for dimensions that are smaller than Ø 40 mm. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation the sealing element must be oiled with system oil.

NOTES
It is recommended to use with minimum two piston guide rings in long stroke cylinders , minimum one guide ring in short stroke and under low radial loads. For special applications that require high temperatures or resistance to chemicals , piston seal is being manufactured with special mixture PTFE and FKM material. The permissible sealing gap values of K17 piston seal is given in the below table.

PERMISSIBLE SEALING GAP
B (mm)	Smax (mm)
x	150 Bar	250 Bar	400 Bar
2.2	0.25	0.20	0.15
3.2	0.4	0.25	0.15
4.2	0.4	0.25	0.20
6.3	0.5	0.30	0.20
8.1	0.6	0.35	0.25
9.5	0.7	0.50	0.30

Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.

More Information
น้ำหนัก/หน่วย (กก.)	0.1000
Application หรือ MEDIA ที่เหมาะกับการใช้งานใช้งาน	Injection moulding machines , fork-lift trucks , loading platforms , cranes , agricultural machinery and valves for hydraulic and pneumatic systems.
Temperature Range Min °C	-30
Temperature Range Max °C	105
Max Pressure	400 bar
หน่วยวัด	mm
แบรนด์	Kastas
OD เส้นผ่านศูนย์กลางวงนอก(มม)	145
I.D. เส้นผ่านศูนย์กลางวงใน	124
THK ความหนา	8.1
Type	K17 PISTON
Part NO	K17 145-124
วัสดุ(Material)	NBR

Account

Account